This content can't be printed from the browser. Use Export PDF with Pro for an offline copy.
An athlete extends the elbow against resistance applied at the hand. In a simplified lever model, which structure acts as the fulcrum?
The hand
The elbow joint
The triceps brachii
The forearm bones
During a two-handed hockey pass, the upper hand acts as the fulcrum, the lower hand applies effort along the shaft, and the ball provides resistance at the blade. Which lever class and force relationship describe this model?
First class with a force advantage
Second class with a force advantage
Third class with a force advantage
Third class with a force disadvantage
A dancer performs a heel raise while the forefoot remains on the floor. Which statements describe the simplified lever model of this action?
I. The ball of the foot acts as the fulcrum.
II. Body weight acts as the load between the fulcrum and effort.
III. The effort is applied at the ankle joint.
I and II only
I and III only
II and III only
I, II and III
A hockey player compares two training sticks. In a simplified model, the upper hand acts as the fulcrum, the lower hand supplies the effort and resistance at the blade is the load. Table 1 compares the sticks when the player's hands remain in the same positions relative to the upper end of each stick.
Table 1. Lever-arm distances for two hockey training sticks
| Stick | Effort arm / m | Load arm / m |
|---|---|---|
| S | 0.30 | 0.90 |
| L | 0.30 | 1.20 |
The player finds it difficult to move the blade against resistance. Explain why stick S would be a suitable choice rather than stick L. Refer to Table 1 and use section 12 in the data booklet.
For stick S, the effort arm is and the load arm is . Calculate its ideal mechanical advantage using , where is mechanical advantage, which has no unit, is the effort arm (m) and is the load arm (m).
The player keeps the upper hand fixed but moves the lower hand towards the blade. Outline how this change affects the effort needed to overcome the same resistance at the blade.
Distinguish between a second-class lever and the third-class lever represented by the hockey stick.
Build a Practice Exam — Sports Science HL
Test your knowledge with a custom paper containing questions from selected topics.


An equipment designer moves the oarlock towards the blade of an oar, leaving the effort and load application points unchanged. The figure shows the simplified lever model, with forces perpendicular to the shaft.
For the same resistance at the blade, which changes occur? The changes are listed in the order: effort arm / effort required to balance the load.
Increases / increases
Decreases / increases
Increases / decreases
Decreases / decreases
A racket player tests a longer racket. Both rackets rotate through the same angle in the same time about the same pivot. The effort arm is unchanged, but the resistance at the striking point acts farther from the pivot with the longer racket. Which prediction correctly identifies a benefit and a cost of the longer racket?
Greater striking-point speed and less effort needed to overcome the same resistance
Greater striking-point speed and more effort needed to overcome the same resistance
Lower striking-point speed and less effort needed to overcome the same resistance
Lower striking-point speed and more effort needed to overcome the same resistance
During a rehabilitation exercise, an athlete holds the forearm horizontal with a weighted cuff near the wrist. The therapist moves the cuff towards the elbow, but it remains farther from the elbow than the biceps attachment. The elbow angle and cuff weight are unchanged. Which statement describes the effect on the simplified lever system?
It becomes second class and requires less biceps force.
It becomes second class and requires more biceps force.
It remains third class and requires more biceps force.
It remains third class and requires less biceps force.
Sports scientists investigated how hand separation affects the use of a hockey stick. Sixteen experienced players used the same adjustable stick. In a simplified lever model, the upper hand was the fulcrum, the lower hand applied the effort, and resistance at the blade was the load.
Table 1. Stationary perpendicular lower-hand effort against the same blade resistance ().
| Hand separation / m | Mean effort force / N | Between-player SD / N |
|---|---|---|
| 0.30 | 80.0 | 8.0 |
| 0.40 | 60.0 | 7.0 |
| 0.50 | 48.0 | 6.0 |
Each player held the stick stationary against the same perpendicular resistance at the blade. The upper hand remained in a marked position. A force sensor measured the perpendicular effort applied by the lower hand at three hand separations. Each player completed three trials per position, and their average was used to calculate the group results in Table 1. Calculate the percentage reduction in mean effort force when hand separation increased from the shortest to the longest distance.
Interpret the relationship between hand separation and effort force in Table 1.
The players then performed shots using each hand separation. Figure 1 shows mean ball speed after contact with the stick. The lower hand remained between the upper hand and blade in every condition. Explain why the stick operated at a force disadvantage in all three conditions.
Discuss whether Figure 1 supports the claim that increasing hand separation always increases ball speed.
Explain why keeping the upper hand in its marked position was important when comparing the stationary effort-force measurements.
Evaluate the reliability of the effort-force measurement procedure.
Build a Practice Exam — Sports Science HL
Test your knowledge with a custom paper containing questions from selected topics.


A rehabilitation scientist investigated an adjustable resistance cuff for archers returning to training after an arm injury. Twelve uninjured adult archers performed elbow flexion with the cuff attached at different distances from the elbow. A simplified model treated the elbow as the fulcrum, the elbow-flexor muscle attachment as the effort point and the cuff as the load. Every cuff position was farther from the elbow than the muscle attachment.
Table 1: Group estimated muscle effort for 12 uninjured archers.
| Elbow-to-cuff distance / m | Mean estimated muscle effort / N | Between-participant SD / N |
|---|---|---|
| 0.20 | 150.0 | 12.0 |
| 0.25 | 187.5 | 15.0 |
| 0.30 | 225.0 | 18.0 |
The cuff exerted the same downward force in each condition. At a standardized horizontal forearm position, muscle effort was estimated using the measured lever arms. The model ignored forearm weight. Table 1 shows the group results. Calculate the mean of the three mean estimated muscle-effort values.
Interpret the effect of cuff position on estimated muscle effort in Table 1.
The archers next flexed the elbow through the same angle in the same time in each condition. A fixed side-view camera tracked a marker on the cuff. Figure 1 shows mean cuff speed along its curved path. Explain how this third-class lever arrangement provides a movement advantage.
Using Table 1 and Figure 1, discuss the claim that the farthest cuff position would be the best choice for an injured archer returning to training.
The order of the cuff positions was randomized separately for each archer. Explain how this design feature reduces the confounding effect of fatigue.
The cuff marker was tracked manually in recorded video frames. Evaluate the reliability of this method for measuring cuff speed.
A badminton player tests a short racket and a long racket in a controlled training drill. Figure 1 shows racket-head speed during the forward swing. For this comparison, each racket rotates about the same fixed pivot at the hand, and both rackets have the same angular speed at corresponding times.
Explain the difference between the racket-head speeds shown in Figure 1 using the properties of levers.
In an unrestricted drill, the player cannot swing the long racket effectively. Outline two changes to the equipment or grip that could reduce the effort required during training.
The player also performs an elbow-flexion exercise with a training weight held in the hand. Explain how each of the following changes would reduce the muscular effort required to support the weight: moving the weight closer to the elbow; increasing the distance between the elbow and the muscle's line of action. Treat these as separate changes. Use section 12 in the data booklet.
The player proposes using the longest available racket in competition. Discuss this proposal in terms of the function of an external lever.
Outline two benefits of internal lever systems for the player's movements, using a different example for each benefit.